10GBase LR SFP+ Transceiver - SFP+ to LC Module 1310nm 10km DOM Duplex LC SMF Optical Transceiver Module Compatible with Cisco SFP-10G-LR Mikrotik

10GBase LR SFP+ Transceiver - SFP+ to LC Module 1310nm 10km DOM Duplex LC SMF Optical Transceiver Module Compatible with Cisco SFP-10G-LR Mikrotik

⏩【High-Speed 10Gbps 】 The 10G LR SFP+ SMF transceiver delivers speeds up to 10Gbps—10 times faster than gigabit networks—making it ideal for ultra HD video, live streaming, and HPC applications. It’s a perfect high-bandwidth solution for data centers and storage area networks (SANs) ⏩【Dual LC & SMF】 This 10g lr single mode sfp+ module features dual LC connectors and operates at a 1310nm wavelength. Designed for long-distance communication, it supports up to 10km transmission with OS2/OS3 dual LC single-mode fiber cables, making itd ideal for large campus and metropolitan area networks (MANs) ⏩【DDM & Hot-Swappable】 With hot-swappable functionality, this 10GBase LR SFP+ module ensures true plug-and-play use—no downtime or complex setup required. Its built-in Digital Diagnostic Monitoring (DDM) enables real-time performance tracking for quick fault detection and easy maintenance ⏩【Low Power & High Performance】 Utilizing high-performance, low-power chips (≤1W), the 10G LR SFP+ to LC single fiber module transceiver ensures stable and fast data transmission. The durable zinc alloy housing improves heat dissipation and extends service life ⏩【Wide Compatibility & Tested Quality】 Fully compliant with SFP+ MSA, SFF-8431 and IEEE 802.3ae standards, YunvoFib10G SFP+ LR module transceiver is rigorously tested to work with Cisco, Meraki, Ubiquiti, Mikrotik, Netgear, D-Link, Supermicro, TP-Link, Linksys, Broadcom, and more open switches The SFP+ LR module electrical interface is compliant to SFI electrical specifications. The transmitter input and receiver output impedance is 100 Ohms differential. Data lines are internally AC coupled. The module provides differential termination and reduce differential to common mode conversion for quality signal termination and low EMI. SFI typically operates over 200 mm of improved FR4 material or up to about 150mmof standard FR4 with one connector. In the transmit direction, the SFP+ transceiver module receives a 10.3125 Gb/s electrical signal (signaling rate) from the host board Asic/SerDes and converts the data to an optical signal via the Laser Driver that controls the Laser diode in the Transmitter Optical Sub-Assembly (TOSA). An open collector compatible Transmit Disable (Tx_Dis) is provided. A logic “1,” or no connection on this pin will disable the laser from transmitting. A logic “0” on this pin provides normal operation. The transmitter has an internal automatic power control loop (APC) to ensure constant optical power output across supply voltage and temperature variations. An open collector compatible Transmit Fault (TFault) is provided. TX_Fault is a module output contact that when high, indicates that the module transmitter has detected a fault condition related to laser operation or safety. The TX_Fault output contact is an open drain/collector and shall be pulled up to the Vcc_Host in the host with a resistor in the range 4.7-10 kΩ. TX_Disable is a module input contact. When TX_Disable is asserted high or left open, the SFP+ module transmitter output shall be turned off. This contact shall be pulled up to VccT with a 4.7 kΩ to 10 kΩ resistor The receiver converts 10Gbit/s serial optical data into serial PECL/CML electrical data. An open collector compatible Loss of Signal is provided. Rx_LOS when high indicates an optical signal level below that specified in the relevant standard. The Rx_LOS contact is an open drain/collector output and shall be pulled up to Vcc_Host in the host with a resistor in the range 4.7-10 kΩ, or with an active termination. Power supply filtering is recommended for both the transmitter and receiver. The Rx_LOS signal is intended as a preliminary indication to the system in which the SFP+ is installed that the received signal strength is below the specified range. Such an indication typically points to non-installed cables, broken cables, or a disabled, failing or a powered off transmitter at the far end of the cable.