Demolition Jack Hammer, 32.6cc 1.63HP 2-Stroke Gas Powered Jack Hammer & Punch Drilling Breaker Engine w/Drill Point Flat Chisel Bit for Crushing,

Demolition Jack Hammer, 32.6cc 1.63HP 2-Stroke Gas Powered Jack Hammer & Punch Drilling Breaker Engine w/Drill Point Flat Chisel Bit for Crushing,

[Powerful Demolition Jack Hammer] - The two-stroke engine with high power (1200W) and large displacement (32.6CC), as well as an enlarged thick-walled cylinder, can achieve a high impact frequency (3200min-1) and impact energy (30J) to easily and quickly penetrate concrete, bricks, rocks, etc with a high speed (5000rpm). [3-in-1 Functions] - Our demolition hammer equipped with three drill bits and two different chisels, it can be used for hammer, drill, or pick by adjusting the knob on the side to meet your diversified needs. Firm Clamping: The collet adopts a clamping design to prevent the drill bit or chisel from falling off. [High-quality Materials] - The aluminum material with a painted process is glossy and can resist wear. Meanwhile, the plastic material is shock-resistant and anti-deformation. The heat dissipation holes on the sides can dissipate heat in time and prolong the service life of this jack hammer. [Easy to Use] - The wireless design can improve the flexibility of operation. You can pull the rope to start the machine. Besides, the throttle switch, one-button flameout switch, and anti-skid auxiliary handle allow for convenient use. The large fuel tank (0.9L) can avoid frequent adding. Meanwhile, the semi-translucent design is convenient for you to observe the remaining fuel quantity and add fuel in time. [Applications] - [Hammer Function] (drilling while hammering), scope of application: applies to drilling holes in concrete, floors, brick walls, stones, and solid walls. It is suitable for electricians and carpenters. [Pick Function] (hammer without drilling), scope of application: suitable for crushing, chiseling, digging, grooving, cutting, and other operations on concrete, masonry structure, and asphalt pavement.

Installation

• 1.Press down the collet.
• 2.Put in a drill bit or chisel.
• 3.Release your hand.
• 4.The installation is complete. 

Notes

• 1.Before each use, please check whether the oil bubble is full of oil. If the oil is not enough, you need to press the carburetor until the oil is full. It is best to press the carburetor every time you use it. Please replace the air filter sponge after 36 hours of continuous operation to avoid damage to the engine cylinder. 
• 2.Please clean up the oil in the carburetor if it is not used for a long time. The carburetor does not need to be replaced if it can be used normally. 
• 3.Please add lubricating oil regularly to ensure strong power.
• 4.Please do not touch the muffler exhaust hole to avoid scalding.
• 5.The mixing ratio of gasoline and engine oil is generally 25:1, but due to the difference of engine oil quality in different regions, we recommend the ratio of 20:1. Please do not use cheap inferior engine oil.

Specification

• Engine Type: Single Cylinder, Air Cooling, 2-stroke
• Impact Frequency: 3200min-1
• Max Torque and Speed: 1.5N.m/5000rpm
• Fuel Mixture Ratio: 25:1 (Gasoline: Motor Oil)
• Fuel Tank Capacity: 0.9L/0.2gal
• Fuel Consumption Rate: ≤0.5L/0.1gal/16Oz Per Hour
• Max Drilling Diameter: 40mm/1.5inch
• Starter System: Hand Pull Start
• Noise: ≤104dB
• Product Size (L*H): 63*24cm/24*9inch
• Engine Size: 36*32mm/14*12inch
• Drill Size: 22*350mm/0.8*13inch
• Point Chisel Size: 18*350mm/0.7*13inch
• Flat Chisel Size: 16*280mm/6*11inch
• Auxiliary Handle Length: 13cm/5inch

Package Included

• 1* Hammer Drilling Machine
• 3* Drills
• 1* Point Chisel
• 1* Flat Chisel
• 1* Fuel Tank
• 1* Funnel